Bmac Care

“Warm up” period

When your Bmac scissors are brand-new and when you receive them back from our repairing and sharpening service, the blades are very sharp and the cutting edge is extremely precise. So, the first cuts with your Bmac scissors will need a “warm up” period as you get used to know how they cut hair.

We suggest a “warm up” period for the first 5-10 hair cuts. During these first hair cuts, please be extremely careful and use your Bmac scissors softly, not making powerful cuts. This way you will be able to enjoy your Bmac scissors at the highest level and to get an excellent cutting condition and feeling for a very long time.

Our Bmac scissors are high performing scissors and fine precision instruments, so please get accustomed to their higher and different performance. Consider your purchase as a long-term investment and you will see that our Bmac scissors will actually cost less because they will last much longer.

When you buy a new pair of scissors, they will probably feel quite different from the scissors you have been using before, so please take the time to get used to their sharpness and to their feeling.


When they are new, your Bmac scissors are in the best condition and they do not need any adjustment.

If in the future you might feel that your scissors need to be adjusted *, please follow this method with great care:

  • if you think that the tension is too loose, then rotate the screw in clockwise direction
  • if you think that the tension is too tight, then rotate the screw in anticlockwise direction

Either case, please adjust the screw little by little and do not loosen or tighten the screw too much. Please be extremely careful in doing this adjustment and never disassemble the mechanism of your Bmac scissors.

Bmac Scissors Europe guarantees complete control over every single pair of scissors we produce and sell. Yet, if you might experience some problems/inconveniences, please contact us.

* The screw adjustment can only be made with our Bmac screwdriver, exclusively supplied on demand.


The sharpening of the scissors should usually be done once a year.

If hair slips on the blades toward the tip of the scissors or if the scissors do not cut as good as they used to, it means that it is time to get the scissors sharpened.

Contact us in order to receive all the information about the sending of your scissors for the repairing service.

Authorized service centres

Please make sure that for the repairing and assistance service you only and exclusively apply to a Bmac agent/distributor, so that your Bmac scissors will be repaired with the original spare parts and with the use of specific sharpening tools and machines in order to guarantee a perfect and long lasting cutting condition to your scissors.

The Bmac manufacturer and the Bmac agent/distributor accepts no liability for any damage or problem caused by the resharpening or servicing which has been carried out by a non authorized service centre or sharpener. For more information on how to care for your Bmac scissors please read our technical advice and suggestions.


Do you have any question? We will be happy to assist.

(+30) 210 22 37 106

Technical advice / Care instruction

  • Your Bmac scissors were designed and built by using very sophisticated and precious parts, so do not disassemble the scissors at any time. If you disassemble the mechanism and then if you do not assemble it properly, you cannot expect the original perfect cutting performance any more. The Bmac agent/distributor and the Bmac manufacturer accept no liability for damages caused by the disassembling of the mechanism
  • Do not leave the scissors blades open and do not use the blade as a knife, always keep them in the closed condition
  • Do not place or carry scissors on top of each other as it may cause damage to the blades or mechanisms
  • After each hair cut, please clean your Bmac scissors with our Bmac microfiber cleaning cloth.
  • Do not wash the scissors with water and do not store them in a humid place in order to avoid rust
  • Avoid placing too strong pressure with your thumb on the thumb ring, because this pressure might cause an unequal strength proportion on the blades, thus compromising the perfect cutting condition of the scissors
  • Do not use the scissors in case the silencer comes off and do not continue to use the scissors when there are nicks along the blades because your hand might be injured or you might enlarge the damage
  • Please pay special attention not to drop the scissors because you might cause unexpected damages or break the blades
  • Do not use corrosive liquids or chemical solutions on your scissors
  • Do not use the scissors having rust because the original performance cannot be expected
  • After you have been using your scissors for some days, please remove all residual hair from the blades with our Bmac microfiber cleaning cloth and store them in a dry and safe place, such as a case
  • When you carry your scissors or send them for the sharpening and assistance service, please put them into their special case provided on purchase

Suggestions and special advice

  • Your Bmac scissors have been studied, designed and produced exclusively in order to cut human hair, so please do not cut any other material and do not use them for any other purpose in order to avoid unexpected problems or injuries
  • Do not use in the case of metal allergy. In case a metal allergy might arise (such as rash or eczema), please consult your doctor and follow his instructions and in case of injury caused by the scissors, please take a first aid and consult a doctor
  • Please pay special attention to the hygienic control and if possible place the scissors in a sterilizer
  • When they are new and after a sharpening service, the blades of your scissors are very sharp, so we highly recommend that you pay special attention while using them
  • Keep the scissors away from children, in a safe place
  • Due to their sharpness please do not touch any part of the blades and do not throw the scissors against people, animals, things and so on
  • Do not place near magnetic objects and do not use any magnetic support in order to avoid unexpected problems and troubles